Whether you are looking to flash a custom ROM, or root your device, TWRP recovery helps a lot. Today, the latest version of TWRP recovery for Galaxy Grand 2 was released, which we’re sharing with you here along with installation guide.
With Galaxy Grand 2 TWRP recovery, you also gain the ability to create full Nandroid backup of the device, which can be sued to retore the device back to current condition, even if you flash a wrong firmware or ROM on it.
Without a doubt, TWRP is an incredible tool, and completely worth it even if you have to break warranty of your device for it, which it does.
KNOX gets tripped when you install TWRP, so know that you won’t be able to use enterprise apps that require KNOX, mostly the apps from your own company where you may be working.
Downloads
- TWRP Recovery for Samsung Galaxy Grand 2: — Link | File: TWRP_ms01lte-beta2.tar (9.37 MB)
- Odin PC software — Link | File: Odin3_v3.10.6.zip (1.6 MB)
→ Check the official downloads page here for the latest version of Galaxy Grand 2 TWRP available at the moment.
Supported devices
- SAMSUNG GALAXY GRAND 2, model no. SM-7105
- Don’t try this on Galaxy Grand 2Â Duos, whose model no. is SM-7102
- Don’t try on any other device whatsoever whose model no. is different than the one provided above!
Important: Check your device’s model no. on its packaging box, or in Settings > About device.
Warning: Warranty may be void of your device if you follow the procedures given on this page. You only are responsible for your device. We won’t be liable if any damage occurs to your device and/or its components. Also, this trips KNOX, meaning KNOX would stop working on your device, and thus you won’t be able to Samsung Pay, or install enterprise Apps on your device at Office.
Backup important files stored on your device before proceeding with the steps below, so that in case something goes wrong you’ll have backup of all your important files. Sometimes, Odin installation may delete everything on your device!
Step-by-step Guide
Step 1. Download Odin and TWRP recovery file from above.
Step 2. Install Galaxy Grand 2 driver (method 1 there!) first of all. Double click the .exe file of drivers to begin installation. (Not required if you have already done this.)
Step 3. Extract the Odin file. You should get this file, Odin3 v3.10.6.exe (other files could be hidden, hence not visible).
Disconnect your Galaxy Grand 2Â from PC if it is connected.
Step 5. Boot Galaxy Grand 2 into download mode:
- Power off your Galaxy Grand 2. Wait 6-7 seconds after screen goes off.
- Press and hold the three buttons Power + Home + Volume down together until you see warning screen.
- Press Volume Up to continue to download mode.
Step 6. Double click on extracted file of Odin, Odin3 v3.10.6.exe, to open the Odin window, as shown below. Be careful with Odin, and do just as said to prevent problems.
Step 7. Connect your Galaxy Grand 2 to PC now using USB cable. Odin should recognize your Galaxy Grand 2. It’s a must. When it recognizes, you will see Added!! message appearing in the Log box in bottom left, and the first box under ID:COM will also show a no. and turn its background blue. Look at the pic below.
- You cannot proceed until you get the Added!! message, which confirms that Odin has recognized your device.
- If you don’t get Added!! message, you need to install/re-install drivers again, and use the original cable that came with the device. Mostly, drivers are the problem (look at step 2 above).
- You can try different USB ports on your PC too, btw.
Step 8. Load the TWRP recovery file into Odin. For this, click the AP button on Odin and the select the kernel’s file you downloaded above.
Step 9. Make sure Re-partition checkbox is NOT selected, under the Options tab. Don’t use PIT tab either. Go back to Log tab btw, it will show the progress when you hit start button in next step.
Step 10. Click the Start button on Odin now to start flashing the TWRP recovery on your Galaxy Grand 2. Wait till installation is finished, after which your Galaxy Grand 2 will reboot automatically. You’ll get PASS message as show below upon successful installation from Odin.
- If Odin gets stuck at setup connection, then you need to do this all again. Disconnect your device, close Odin, boot device into download mode again, open Odin, and then select the file and flash it again as said above.
- If you get FAIL in the top left box, then also you need to flash the file again as stated just above.
→ That’s it. Enjoy TWRP recovery on your Galaxy Grand 2!
Root Galaxy Grand 2
Now, that you have the TWRP recovery, flash the SuperSU file now to see if you gain root access.
If you need any help with this, let us know via comments below and we will try our best to help you out.
Via aapav01
Thanks a lot for sharing this post its really help full. i followed the above steps and i got everything done with no errors. But when i load in recovery mode i get recovery mode screen for few seconds then it simply loads the loads the OS. Any help is really appreciated Thanks once again
Do you see TWRP screen (blue colored in black background) for those few seconds? Do you see buttons for Install, Wipe, Backup, etc?
Thanks a lot for sharing this post its really help full. i followed the above steps and i got everything done with no errors. But when i load in recovery mode i get recovery mode screen for few seconds then it simply loads the loads the OS. Any help is really appreciated Thanks once again
Do you see TWRP screen (blue colored in black background) for those few seconds? Do you see buttons for Install, Wipe, Backup, etc?
me too having the same problem sir
me too having the same problem sir
oiga mis controladores no aparecen que hago??? osease antes conectaba mi cel y aparecia, asi no usara el odin, pero ahora ni para el odin me sirve q hago???
oiga mis controladores no aparecen que hago??? osease antes conectaba mi cel y aparecia, asi no usara el odin, pero ahora ni para el odin me sirve q hago???
nand write start
fail and over…..