The latest TWRP recovery v3.0.0-0 is now available for the Galaxy Ace 3 (thanks to kotzir!). Because it’s quite new, it may contain bugs, which is why we’re also providing old and stable version 2.8.7.0 of the TWRP recovery below. In case TWRP 3.0 doesn’t work, simply install v2.8.7 back to keeps things running.
Do let us know via comments section below whether it works as intended or not for your device.
Downloads
- Galaxy Ace 3 LTE TWRP Recovery:
- Odin PC software — Link| File: Odin3_v3.10.6.zip (1.6 MB)
In case link doesn’t work, do let us know via comments section below the post.
Supported devices
- Samsung Galaxy Ace 3 LTE, codename loganreltexx, model no. GT-S7275
- Don’t try on any other device whatsoever!
Warning!
Warranty may be void of your device if you follow the procedures given on this page. You only are responsible for your device. We won’t be liable if any damage occurs to your device and/or its components.
Backup!
Backup important files stored on your device before proceeding with the steps below, so that in case something goes wrong you’ll have backup of all your important files. Sometimes, Odin installation may delete everything on your device!
Step-by-step Guide
Step 1. Download Odin and TWRP recovery file from above.
Step 2. Install Galaxy Ace 3 LTE driver (use method 1 on the page linked) first of all. Double click the .exe file of drivers to begin installation. (Not required if you have already done this.)
Step 3. Extract the Odin file. You should get this file, Odin3 v3.10.6.exe (other files could be hidden, hence not visible).
Step 4. Disconnect your Galaxy Ace 3 LTE from PC if it is connected.
Step 5. Boot Galaxy Ace 3 LTE into download mode:
- Power off your Galaxy Ace 3 LTE. Wait 6-7 seconds after screen goes off.
- Press and hold the three buttons Power + Home + Volume down together until you see warning screen.
- Press Volume Up to continue to download mode.
Step 6. Double click on extracted file of Odin, Odin3 v3.10.6.exe, to open the Odin window, as shown below. Be careful with Odin, and do just as said to prevent problems.
Step 7. Connect your Galaxy Ace 3 LTE to PC now using USB cable. Odin should recognize your Galaxy Ace 3 LTE. It’s a must. When it recognizes, you will see Added!! message appearing in the Log box in bottom left, and the first box under ID:COM will also show a no. and turn its background blue. Look at the pic below.
- You cannot proceed until Odin recognizes your device and you get the Added!! message.
- If it doesn’t, you need to install/re-install drivers again, and use the original cable that came with device. Mostly, drivers are the problem.
- You can try different USB ports on your PC too, btw.
Step 7. Load the TWRP file into Odin. For this, click the AP button on Odin and the select the file you downloaded above.
Step 8. Make sure Re-partition checkbox is NOT selected, under the Options tab. Don’t use PIT tab either. Go back to Log tab btw, it will show the progress when you hit start button in next step.
Step 9. Click the Start button on Odin now to start flashing the TWRP on your Galaxy Ace 3 LTE. Wait till installation is finished, after which your Galaxy Ace 3 LTE will reboot automatically. You’ll get PASS message as show below upon successful installation from Odin.
- If Odin gets stuck at setup connection, then you need to do this all again. Disconnect your device, close Odin, boot device into download mode again, open Odin, and then select the TWRP and flash it again as said above.
- If you get FAIL in the top left box, then also you need to flash the firmware again as stated just above.
→ That’s it. Enjoy the TWRP recovery on your Galaxy Ace 3 LTE!
To access TWRP recovery, you have to reboot into recovery mode:
- Power off your Galaxy Ace 3 LTE. Wait 6-7 seconds after screen goes off.
- Press and hold the three buttons Volume up + Home + Power together until you see Samsung logo on the screen.
If you need any help with this, let us know via comments below and we will try our best to help you out.
Discussion